Did you know?

The Litter-Robot arrives with the automatic night light function enabled. You can set the light to always on, off, or automatic as well as adjust the brightness of the night light. When the light sensor, located in the control panel, detects low-light conditions, the night light turns on automatically. Turn the Litter-Robot off and unplug the unit. Remove the Bonnet: Press and release the snap tabs on both sides of the Bonnet, then lift and rotate the Bonnet off of the Globe and carefully set it aside. Remove the Globe: With two hands, lift the Globe off the Base. Clean the Globe with water and a mild soap. Toll Free: 877-250-7729 www.Litter-Robot.com 10 the Control Panel or by turning the unit OFF then ON with the switch on the back of the Base. If you accidentally over-fill the globe, excess litter will be expelled into the waste drawer. At the end of the cycle, the litter bed will be leveled. The Litter-Robot arrives with the automatic night light function enabled. When the light sensor, located in the control panel, detects low-light conditions, the night light turns on automatically. The automatic night light, located in the upper bonnet, is there to help guide your cat to the litter box. A light sensor located above the Cycle ...

Litter-Robot 3: Buttons and lights. Control panel buttons . Power. Press and release the Power button to turn the robot ON of OFF. The robot will begin a clean cycle when power is turned on. Press and hold, while at the home position, to … Litter-Robot is equipped with a control panel lockout feature. When activated, this feature will disable the button functions to prevent unwanted changes. While in control panel lockout mode, the light bar will flash red when any button is pressed, indicating the control panel is locked. FAQ. Our Final Verdict. We give Litter-Robot 3 litter box a rating of 4.6 out of 5 stars overall. 96. 90. 80. 90. The Litter-Robot 3 is a dream come true for cat owners. This premier litter box ...Using a combination of time, gravity, and rotation, the Litter-Robot deposits the clumps into a waste drawer below the globe, leaving a clean bed of litter for your cat every time. Just empty the waste drawer when indicated by the app or …Litter-Robot 3: Cat Sensor Troubleshooting Litter-Robot 3: Control Panel Lockout Litter-Robot 3: Cycle delay setting ; Litter-Robot 3: Deep Cleaning Litter-Robot 3: Filling the Globe ; Litter-Robot 3: Fixing a Loose Gear

1. Place the Litter-Robot in the same location as the current litter box, set it up (make sure you add litter to the Globe), and make sure it is turned off. Give your cats a day or two to explore the Litter-Robot. If your cats show no interest, entice them to ap-proach the Litter-Robot by using some catnip or a favorite treat. 2.Make sure that the green light on the Litter-Robot is considerable, or you have noticed the sensor is Control Panel is on (“OK/Waiting”). Page 11: Adjusting The Cat Sensor SensitivityLitter-Robot takes the yucky task of scooping off your hands. Neutralize litter box odors, and give kitty a clean bed of litter every time with Litter-Robot 4. ... Adjust the Litter-Robot cycle delay, lock out the control panel, activate the night light, or even schedule sleep mode from the Whisker app! Cat Recognition. Laser and weight sensor ... ….

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Litter robot control panel. Possible cause: Not clear litter robot control panel.

Litter-Robot 4 is the latest evolution of the highest-rated WiFi-enabled, automatic, self-cleaning litter box for cats. With over 20 years of customer feedback driving product innovation, Litter-Robot 4 features new sensor and litter-sifting technology for enhanced odour control, cat safety, and real-time tracking of waste and litter levels through the …Control Panel Lockout disables buttons to prevent unwanted changes from being made. Litter-Robot functions normally in Automatic Mode while the Control Panel Lockout is activated. Activating Control Panel Lockout: Press and hold the Reset button for about 5 seconds to enter or exit Control Panel Lockout. The blue light will blink to confirm status.

buttons on the Litter-Robot 4 control panel for 3 seconds, or tap "Replace Filter· under Controls in the Whisker app. O Remove the filter cover: Lift the small notch to release the filter cover snaps from the globe. Set aside the filter cover. 0 O Place the opened Odor Trap® Holder on the filter cover. The center arrow on the OdorTrap®Ensure proper placement. Your Litter-Robot comes fully assembled and ready to use. Get started by following the steps below. If possible, place Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is on a firm, level surface in a cool, dry location. Locate the unit near a power outlet.1. Reassemble the Bezel onto the Circuit Board and Keypad by holding the Circuit Board upright and fitting the Bezel over it, so that the buttons come through the Control Panel. Make sure to keep the silicone Keypad wrapped around the edges of the Circuit Board. 2. Make sure the edges of the Bezel rest flush with the Base.

33funds Litter-Robot is equipped with a control panel lockout feature. When activated, this feature will disable the button functions to prevent unwanted changes. While in control panel lockout mode, the light bar will flash red when any button is pressed, indicating the control panel is locked. kamo hoopstt newspapers Control Panel - Light Bar..... 20 Sensors and Functions ........................................................................................................................................ 21 Cat Presence ... The Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels. OmniSense™ also supports the SafeCat system which continuously analyzes four safety zones to ensure your cat is always safe. There are three laser sensors located in the top of the ... gloucester nj obituaries To reset the Cat Sensor, the unit must be at the Home position with a solid blue light displayed on the control panel. If you press Reset while the unit is cycling, it will pause the cycle; simply press Cycle to restart the cycle or Reset to abort the cycle and return the Globe to the Home position. (If you press and hold the Reset button for ... Why upgrade to Litter‑Robot? The problem with a traditional litter box isn’t just this unpleasant chore. It’s also the foul odors, messy litter tracking, territorial issues in a multi-cat home, and more. With Litter-Robot, self-cleaning technology automatically removes the waste for you. You only need to empty the waste drawer when it’s ... beach naturist picswillow creek apartments kalamazoofairbanks fuel prices Empty the Waste Drawer when indicated by the Light Bar flashing blue on the Control Panel. How often you will need to empty the Waste Drawer depends on the ... new china bethalto il The remote acts as a wireless control panel for the Litter-Robot. Control everything in the app with the remote, such as updating your nickname, changing sleep mode, updating wait time, turning on and off your night light, and activating panel lockout. The remote also allows you to reset the gauge when you empty the unit, helping the app learn ... produce junction allentownmadisonville tx directionsdj akademiks height and weight Litter-Robot is equipped with a control panel lockout feature. When activated, this feature will disable the button functions to prevent unwanted changes. While in control panel lockout mode, the light bar will flash red when any button is pressed, indicating the control panel is locked. 1. Place the Litter-Robot in the same location as the current litter box, set it up (make sure you add litter to the Globe), and make sure it is turned off. Give your cats a day or two to explore the Litter-Robot. If your cats show no interest, entice them to ap-proach the Litter-Robot by using some catnip or a favorite treat. 2.